I'm pretty much done on the planning stages of my TBH's. See the Equipment Forum for the Sketchup File.
My question is what thickness top bars are you guys using? These will be standard 19" long and 1.25" wide. I have them spec'ed out to 1" thick right now but it would be a lot simpler to use the stock the boxes are built out of instead of cutting down 2x4s. Is 3/4" stiff enough?
I plan to use 3/4" stock for my topbars (my lumber just arrived today!), but I don't really have any experience with this. Hope fully someone else will chime in here.
However I took a look at your SKP file, and noticed you have slots for a removable bottom board. I would be concerned that a thin piece of sheet material spanning the full length of the hive, hinged only on two sides, will start to sag and fall out over time. You may need to reinforce the bottom board with battens.
Good point on the bottom board. I'll be using some corrugated plastic (stuff used for yard signs) for the board. I'll see how it sags. I might glue a small strip down it's length perpendicular to stiffen it up. I've also uploaded a new SKP file with my latest refinements. Same Link I added in a couple of back holes in the corners for doing spits and added in the follower boards.
My top bars are 5/8 of an inch and I haven't had any problems with them. Sometimes I'll get one that is only half an inch because it comes from the last part of the piece of wood I'm cutting. I haven't had a problem with these either (rather take advantage of it than let it go to waste). Knots, however, can give you a problem.
The design is basically a wide Lang. I don't plan on using it with any lang equipment (except for maybe installing a nuc) but it's nice to have the option if I need it. Since I won't be using it as a lang, 3/4" it shall be. It will really simplify the woodworking. Thanks for the feedback.
There are a few ways to loose a comb. Flex the comb and it's gone. Or flex the top bar and it's gone.
Rather than think thickness, thick rigidity which is a affected by thickness, length, load and top bar configuration. A larger comb, moving or stacking hives, and setting on the top bars all increase the loading.
So, do a test. Build a prototype. Support it on its ends. And apply pressure in the middle. If you don't like the way it flexes, go thicker.
I used 3/4 inches for my first 22" long bars. They had a 1/4" saw kerf used to make a "T" type top bar reinforcement. That cut, even with the wood slat glued in, unacceptably reduced their rigidity. Increasing the thickness to 1" stiffened it back up.
I've seen shorter top bars that are 2" thick. That is probably an overkill.
Winter insulation is also a factor - the thicker the better if you don't have additional insulation between top bars and cover - but 2" does seem excessive.
I'm pretty much done on the planning stages of my TBH's. See the Equipment Forum for the Sketchup File.
My question is what thickness top bars are you guys using? These will be standard 19" long and 1.25" wide. I have them spec'ed out to 1" thick right now but it would be a lot simpler to use the stock the boxes are built out of instead of cutting down 2x4s. Is 3/4" stiff enough?
for my top bars. I use stock 1 x2 's. I've had a few warp. I had one bar with honey that weighed 15 lbs with no problems. Look what thickness a Lang has. I'm in Texas so cold is not an iussue for me.
In my first hive I was trying to save money by getting 15 bars out of a 2x4, which made each one about a half-inch thick. During winter, these bars (thinner than my hive walls) wanted to condense water. So, I echo and endorse those who talk about insulation. Your top bars should be thicker than your side walls so the water condenses on the walls. 3/4 is stiff enough, but 1 - 1.25" is better.
The 2x4 lumber is most plentiful, free lumber you can get.
I have so much 2x4 stuff, I don't care take more of it (no room).
In your area, don't people dump 2x4s (and lots of other wooden material - 2x, plywood, etc, etc)?
Do you actually look for it?
All of life is a tradeoff. Thicker bars are better insulation and more stable (less likely to bend or sag) but they also make a bigger space for bees to get squished when putting bars back together. The thinner they are the more the bees find their way up or down as you push them together. The thicker they are the more they get squished...
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Beesource Beekeeping Forums
1.8M posts
54.7K members
Since 1999
A forum community dedicated to beekeeping, bee owners and enthusiasts. Come join the discussion about breeding, honey production, health, behavior, hives, housing, adopting, care, classifieds, and more!