Search Results - Beesource Beekeeping Forums

Search:

Type: Posts; User: Little boy blue

Page 1 of 10 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    The posts are from a foot length of 3/8 or 10.00mm stainless steel, I made the main posts out of it too.

    There is lots of these depos in the US, one near you I would think.
    ...
  2. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    That is a good one and you will have amps in reserve, good price and it has out sockets as standard.
  3. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    Electricity is a funny beast, but the power unit you have is ideal for many other things, I have a similar one and its really handy to have.
  4. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    What is happening is your creating resitance so you need a higher amps and volts, its like driving a large Chevy with a small engine if that makes sense.

    This is my unit,...
  5. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    I dont think your going to have enough amps to heat the coil, the item you have shown is only one amp and will be working on max all the time, you would be far better going for one of these 5 amp...
  6. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    I would give it a go, when you first heat the coil it can tend to change shape slightly, so when you have first run it, let it cool down again and re-shaape it, I found that the thinner gauge 1.00mm...
  7. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    That would be good, would be interested in how it goes.
  8. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    Use a section of K & S brass tubing to slide over a guide post made from a thick round nail and drill a wooden dowel to take the brass tube so it slides nice and there's your drop weight.
  9. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    I used a short section of aluminum tube and turned a hardwood insert and drilled an 8.00mm hole in the centre to slide over an 8.00mm post set in the base.
    I'm going to mod the drop weight on my rig...
  10. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    I agree with you entirely J C, independance is my preffered paradigm, and you will most likely be asked for making some tips for others as I did.

    Dan.
  11. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    I settled for a short drop of 30.00mm below the bottom of the drop weight and the base, this gives shorter tips like Teplov's which are slightly stronger at the tip, which also make a better seal...
  12. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    I evenntually found as decent scope and have been busy practicing the art of insemination down at my freinds yard. I also have a new site much nearer to home a couple of minutes walk on private...
  13. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    The step by step process of how I made my tip puller is in the pages of this thread and is a lot to relist, but if there is any specific item you need to know about I will try to guide as best as I...
  14. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    What you need is more amps by using the best tool called a variac or a mains dimmer switch so you can fine tune the voltage, you can get it right using a battery charger but everything needs to be...
  15. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    In the video of the guy using a large battery charger you can hear the charger set to its boost power setting.

    To create enough amps you will need a large battery charger to do the job.

    However...
  16. Replies
    16
    Views
    2,123

    Re: Vibration table/ mite shaker

    How about an ultrasound device tuned into the mites frequency to zapping the little beast's as the bees enter the doorway.
  17. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    The latest design under the 3D printer model is this much simpler design using only 17 separate pieces and standard glass tube inside brass tube queen posts.

    All glass items are standard off of...
  18. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    JC

    Test the light using a thermometer at roughly the distance you will be using it from the Queen post.

    Teplov uses the same scope he will know how it performs.
  19. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    I'm currently building a reflector mirror setup that reflects pure sunlight through a liquid lens to cool the UV light.

    Failing that there are many cheaper led lights on the market that have a...
  20. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    The second of my 3d units now ready for printing.

    This one has X & Y positive tracking via a dovetail on the Base and a hinge with left and right hand threaded cylinders using an internal...
  21. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    http://i63.tinypic.com/3eomf.jpg

    http://i67.tinypic.com/1r6vit.jpg

    http://i68.tinypic.com/2hz5v8l.jpg
    https://s4.postimg.org/6le07v29p/3_D_bodies_ass.jpgupload gif from url

    Section view of...
  22. Re: Cell Punch Queen Rearing method on youtube

    Howdy

    If you sharpen the thin brass tube on the inside edge, as you cut the plug the outer diameter of the tube is slightly wider than the inner surface and creates a slight wedging motion, and...
  23. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    https://s15.postimg.org/rzjf6qdnv/bee_ass_II.jpgimage hosting over 5mb

    https://s17.postimg.org/spo68m1y7/image.jpg

    https://s17.postimg.org/itn38yw67/assfg.jpg


    upload an image

    Above is a...
  24. Replies
    565
    Views
    92,872

    Re: Instrumental Insemination Equipment

    You could do it easy and people save €900.00.
  25. Re: Cell Punch Queen Rearing method on youtube

    My mini's which I built 50 of several years back to the Cushman plans.

    All dovetail construction for dry strength and longevity not glued and easily taken apart if needed.

    All done using a...
Results 1 to 25 of 242
Page 1 of 10 1 2 3 4