My new extractor will extract (80) frames at a time. That equates to about 250-300 lbs (about 25 gallons max.) of honey a load being discharged out of the extractor. My current sump/clarifier is the 15 gallon, small, unheated one from Dadant. Do I need a larger sump/clarifier? My question is: Does a sump/clarifier need to be large enough to hold at least one entire extraction load?
My new extractor has a 4" outlet on the side wall at the bottom of it and my old sump/clarifier only has a 1 1/2" inlet and 1 1/2" outlet..... Is that going to be a problem?
I think he was asking about a sump not a holding tank. I have a large sump. holds about a barrel of honey. I have it on a float switch so it gets almost full to the top before kicking on. If I were you I would put heat to that sump you have some how. it really helps the wax float to the top faster and you wont suck so much up into your nice clean honey holding tank. then you just skim the wax off a couple times of day off your sump and that is a lot easier than climbing up a ladder or what ever to skim your tank. I turn my sump on a hour before I start extracting and I turn the heat up according to how fast im going. don't want to burn any honey sitting in the sump for to long. but when im up and running I have it at like 150degrees. just don't forget to turn in down if you stop for a bit.
I have a large jacketed kelly sump that wee have a 33 frame dumping into. It had the 1 1/2 inlet and outlet. The outlet is not a problem but the inlet was. We disconnected the pipe from the inlet and let it run into the top of the tank and that helped a lot.
Sorry about that. I am talking about the sump. Does the sump capacity need to be as large as at least one load from the extractor? If I have an extractor that can extract 20-25 gallons in one load, does the sump need to be at least 25(+) gallons or will my current 15 gallon catch most of the wax. My goal is to catch as much wax in the sump before it goes to holding tank. I am trying to minimize the amount of "skimming wax from the holding tank as possible".
A beekeeper that I know with a 28 frame Cowen line has that same 15 gal sump and has commented that it really isn't big enough. I am thinking that you will want a larger one so that the output from your last run is sitting in the sump while you are loading the next run.
I guess it's a matter of degrees and how complicated and expensive you want to get. The short answer is a sump that hold less that the capacity of your extractor is going to result in a faster build up of wax in your holding tank. The bigger the better but no clarifier is going to be perfect. Accept that fact that you will have to, at least occasionally, skim your holding tank. Why not just think of a little wax in your tank as a protective layer, I assume you aren't going to be bottling directly out of it.
I had a 30 gallon unheated sump that I use to use, but I found myself having to skim the holding tank each week.
My new sump is a 70 gallon with a heated water jacket. Only have to skim the holding tank off 2 to 3 time in a season. If I'm going to bottle a load, I'll hold back a load in the sump and pump it in the morning. That way I don't have wax in the bottling tank. The bigger sump with heated is a whole lot better.:thumbsup::thumbsup::thumbsup:
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Beesource Beekeeping Forums
1.8M posts
54.7K members
Since 1999
A forum community dedicated to beekeeping, bee owners and enthusiasts. Come join the discussion about breeding, honey production, health, behavior, hives, housing, adopting, care, classifieds, and more!