Results 1 to 20 of 23

Hybrid View

  1. #1
    Join Date
    May 2013
    Location
    Gladys, VA
    Posts
    91

    Default Screws or Nails?

    Ready to assemble my deep NUC body along with other ten frame boxes. Comes with nails but was thinking of using wood screws. Seems like it would be more secure in the long run. What has been your experience?
    ----
    Joe

  2. #2
    Join Date
    Nov 2012
    Location
    Gonzales, Louisiana, USA
    Posts
    170

    Default Re: Screws or Nails?

    Quote Originally Posted by tibadoe View Post
    Ready to assemble my deep NUC body along with other ten frame boxes. Comes with nails but was thinking of using wood screws. Seems like it would be more secure in the long run. What has been your experience?
    Well...I think screws are stronger than nails...But I think a good quality wood glue is stronger than either, and the most important component of assembly!

    I use Titebond III, a lot of folks will tell you Titebond II is sufficient, and they're "probably" right, but I like a little over-engineering! ...I finish it of with pneumatic staples.

    If you are going to use glue, I think nails are more than sufficient...If you're not going to use glue, I think screws is the better choice, but still don't think it will match up to basically any reasonable fastener used in conjunction with a quality glue....But understand, as with EVERYTHING in Beekeeping, opinions do vary!

  3. #3
    Join Date
    May 2013
    Location
    Concord, NC, USA
    Posts
    19

    Default Re: Screws or Nails?

    I use screws exclusively. But I only have seven hives so the extra cost and extra time are of no concern to me.

    Why? I have a large wood deck and have grown tired of fighting the nails that keep popping up through the seasons. I figure why fight the same potential problem on my hives. Fix it once and for all. I also predrill all my screw holes to eliminate any chance of splitting the wood.

    It works for me.
    "Everything turns to dust -and there is nothing you can do to stop it".

  4. #4
    Join Date
    Aug 2007
    Location
    Fairfield County, Connecticut, USA
    Posts
    3,589

    Default Re: Screws or Nails?

    Use screws with TiteBond II or III glue....

    I seal over the exposed end grain with TiteBond as well. Same for the heads of fasteners.
    BeeCurious
    Trying to think inside the box...

  5. #5
    Join Date
    Jan 2013
    Location
    Midland, MI
    Posts
    568

    Default Re: Screws or Nails?

    USE GLUE! titebond II or Titebond III will work fine. I like the advertised qualitites of III better, but I buy II in the gallon jugs. TBIII is less viscous than TBII so i find that it makes for more of a mess when I'm assembling parts.

    To answer your fastener question, if you're going to nail themn together with naisl and a hammer, I'd use screws. if you're using an air nailer/stapler then I'd go with staples. I'm sure screws are better overall, but air nailing is WAY faster. Last night I cut out and assembled 7 deeps, 10 bottom boards, 10 covers, and 12 5-frame nucs. I doublt i would have gotten them all assembled is I was hand nailing or screwing.

    Fortunately, whatever decision you make will be the correct one as long as you use glue as well


    use glue


    glue.

  6. #6
    Join Date
    Apr 2013
    Location
    Marshall county, AL
    Posts
    756

    Default Re: Screws or Nails?

    Quote Originally Posted by KPeacock View Post
    but I buy II in the gallon jugs.


    use glue


    glue.
    Titebond III comes in gallons too. I own one of them. It is thick glue. I glue everything. All joints on all woodenware and frames.


    Oh, and to the original poster. USE GLUE! LOL I glue and staple my boxes together initially to get them together faster and then usually put about 3 screws per joint before the glue sets. I am building some nucs now and have not used any screws, just glue and staples. I may go back and put screws. The first boxes I got were some that I bought. They were nailed together with no glue. Stupidity at its finest. After one season they are coming apart at the seams. Those were the fancy finger jointed boxes. I use lap joints on the ones I build. Boxes I built less than a month after buying the ones last year have absolutely no separation at any joint. They were glued and screwed together. I am going to remove the 4 boxes that I purchased and take them apart and glue and screw them together before they start to rot.

  7. #7
    Join Date
    Dec 2005
    Location
    Brasher Falls, NY, USA
    Posts
    26,089

    Default Re: Screws or Nails?

    Nails
    Mark Berninghausen "That which works, persists."

  8. #8
    Join Date
    Aug 2007
    Location
    Fairfield County, Connecticut, USA
    Posts
    3,589

    Default Re: Screws or Nails?

    Quote Originally Posted by tibadoe View Post
    Ready to assemble my deep NUC body along with other ten frame boxes. Comes with nails but was thinking of using wood screws. Seems like it would be more secure in the long run. What has been your experience?
    Quote Originally Posted by sqkcrk View Post
    Nails
    Really?

    From "your experience" you've decided that nails are more secure or are you simply stating (in a brief manner) that you use nails?
    BeeCurious
    Trying to think inside the box...

  9. #9
    Join Date
    Dec 2005
    Location
    Brasher Falls, NY, USA
    Posts
    26,089

    Default Re: Screws or Nails?

    Quote Originally Posted by BeeCurious View Post
    Really?

    From "your experience" you've decided that nails are more secure or are you simply stating (in a brief manner) that you use nails?
    I use nails. Screws cost more. You can't drive them w/ a hammer. They cut end grain. Nails is what I use and prefer. Staples are faster. I don't need to be faster. Faster is dangerous, sometimes. Power tools mean that mistakes can be made faster. But that's me.
    Mark Berninghausen "That which works, persists."

  10. #10
    Join Date
    Sep 2011
    Location
    Reno, NV
    Posts
    2,810

    Default Re: Screws or Nails?

    Mark you comment above reminds me of this definition of a Table Saw. "An expensive and highly precise machine used for cutting lumber to short".
    Stand for what you believe, even if you stand alone.

  11. #11
    Join Date
    Sep 2009
    Location
    Millbury, MA, USA
    Posts
    1,787

    Default Re: Screws or Nails?

    narrow crown staples

  12. #12
    Join Date
    Sep 2011
    Location
    Reno, NV
    Posts
    2,810

    Default Re: Screws or Nails?

    Box joint and nails. How well it holds has more to do with the quality of wood (Generally bad) than the fastener.
    Stand for what you believe, even if you stand alone.

  13. #13
    Join Date
    Feb 2014
    Location
    Ridgeville, SC, USA
    Posts
    41

    Default Re: Screws or Nails?

    Glue then 2 screws per side and finish with crown staples or nails. The screws pull corners tight.

  14. #14
    Join Date
    Jul 2011
    Location
    Denver, Colorado, U.S.A.
    Posts
    735

    Default Re: Screws or Nails?

    I use Tightbond III and 2-1/2" x 12ga stainless steel ring shank nails.

    https://www.tupent.com/shop/stainles...238/index.html

    The ringshank nails hold better than regular nails and go in faster than a screw. I drive 'em in with a 2-1/2 lb sledge hammer. Two strokes per nail and the joint is tight with glue squirting out. The 12ga nail is thinner than a screw and so less chance of splitting the wood, and the stainless steel nails won't rust. The ringshank nails hold things real tight while the glue hardens. Once the glue has dried, the joint is rock solid, and I don't think the fastener contributes much to the strength so screws provide no advantage, IMHO. I coat the end grain with the glue so it is sealed really well.

    Lots of ways to skin this cat, though.
    Last edited by shinbone; 03-31-2014 at 08:45 PM.
    --shinbone
    (3rd year, 14 hives, Zone 5b, 5400 ft, 15.8" annual rainfall)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Ads