foundation starter comb

**Harley Craig** · 10-23-2012, 07:21 AM

Has anyone tried using foundation attached to some top bars to try to get your bees to build straight comb right out of the gate? What would be the best way to attach it if so?

**shannonswyatt** · 10-23-2012, 09:47 AM

This is what Wyatt Mangum does. He puts a groove in the bar and then uses melted wax to attach it. He has made a jig to setup a series of bars and pour the melted wax down 8 or 10 or so at a time.

I have considered making a bar with a split wedge. There would be a fixed wedge on the bar and then you would attach the other half with nails or staples. Then you could just wedge the strip in place. You could do this by using a router to route away half of the wedge.

The thing I don't like about using a starter strip is that as soon as you attach the starter strip you have to be careful with the bars. And if you drop them you can pretty much bet the strip will be knocked off.

**PAHunter62** · 10-23-2012, 07:13 PM

There is a tool called a Wax Tube Fastener that some will use to attach a foundation starter strip to a grooved top bar. You can see a demo of it on Linda Tillman's blog:

http://beekeeperlinda.blogspot.com/2...stener_26.html

What I have done, and like, is to glue in a wooden strip into the top groove. I don't even add any wax, the bees take right too it and build off the strip. Adding in new foundationless frames in between brood comb works well, or between capped honey frames. Don't add them between uncapped honey frames or the bees will just keep extending the comb to each side instead of working on the new frame.

Good luck.

**shannonswyatt** · 10-23-2012, 07:18 PM

Yes, I don't think that starter strips are necessary if you give them an idea of were to pull the comb by using a stick or a wedged bar. Some folks say don't use wax on your bars as it will actually make the contact with the bar weaker.

**Steven Ogborn** · 10-23-2012, 07:36 PM

My top bars are made with a plastic strip. I ripped down a bunch of foundation from my Lang stuff.
They end up ridged and permanent when glued in. They look like this.http://s1066.photobucket.com/albums/...3DIMAG0044.jpg

I had NO issues with cross-combing with the hives that I used these in this year.

**Harley Craig** · 10-23-2012, 08:13 PM

Thanks for the replies I have wedges made from cove molding in one hive and wood strips in grooves in another just to see which I like better. I have seen alot of videos where the comb curves at the ends and ends up off the bars, and wondered if one or two straight ones would help get them on the right track. Steven that is exactly what I was thinking but more foundation than just a strip. Thought about trimming some plastic foundation in the shape of a top bar comb and hot gluing it into place and then painting with wax to encourage comb building on the plastic cell. One established straight I would phase out the top bars with foundation

**Steven Ogborn** · 11-01-2012, 06:14 PM

Originally Posted by shannonswyatt

This is what Wyatt Mangum does. He puts a groove in the bar and then uses melted wax to attach it. He has made a jig to setup a series of bars and pour the melted wax down 8 or 10 or so at a time.

I have considered making a bar with a split wedge. There would be a fixed wedge on the bar and then you would attach the other half with nails or staples. Then you could just wedge the strip in place. You could do this by using a router to route away half of the wedge.

The thing I don't like about using a starter strip is that as soon as you attach the starter strip you have to be careful with the bars. And if you drop them you can pretty much bet the strip will be knocked off.

That's why I used the plastic foundation, it's hard. Then I just used Titebond II to glue them in. Now if I can get my lazyself to put a rabbet cut on the ends of my top bars they'll actually fit into a Lang box if needed. Waxing stuff is hard. It took what seemed like forever to just fill the kerfs in my bars last year.

**julysun** · 11-01-2012, 08:23 PM

Steven O; Your post fits my plan to move my TBH comb into a Lang deep. Screw an extender to each end of a top bar so it will fit into the lang then move all the frames. Shortly after I will burn and bury all parts of the TBH.
Also I had planned to try Titebond glue on 2" wax strips as satrter strips, I have been tacking them in. I also use tongue depressors for starter strips. Without alternating comb or foundation filled frames my bees pull wax to wide. Sometimes me and the bees seem to be working at cross purposes!

After this move to the Lang over time I will work out all the modified TBH frames.
Also; It will be easy for me to wax dip (my own wax) and dry the depressors before gluing them into a frame!!!

**Stuart** · 11-12-2012, 05:00 PM

Here's the easiest method I've found. Simply melt some wax block into a grove with a torch (be careful) and stick a strip of foundation in there. The wax will drip/pour nicely off of a bottom corner. You can't be timid about this because the wax will cool and harden. Just fill the groove reasonably quickly and it'll stay soft enough to join with the foundation. I've never had cross comb and the only annoyance is if I make them too short (more than an inch from the side) because they'll start to curve the ends.

Stuart

melting wax.jpg installing foundation.jpg

**Delta Bay** · 11-13-2012, 09:07 AM

The foundation starter strips as Stuart presents have always giving me a 100% success rated. The curving of comb at the ends can be avoided by using foundation strips with a greater depth running it the full length of the bars with no more than a bee space between the foundation strip ends and hive wall. The curving is caused due to the extension of cell walls for honey storage and having no barrier comb to regulate the extra cell wall length that is built causing the bees to curve the next comb built to curve around it maintaining the bee space. Starting out fresh without a supply of combs I feel this is the way to go especially for beginners with no natural comb experience.
The top two inches of comb construction is, mostly at the comb ends, where this takes place.
Once there are several well built straight combs in the hive most any of the guides are suitable.

**Steven Ogborn** · 11-19-2012, 11:44 AM

Originally Posted by Stuart

Here's the easiest method I've found. Simply melt some wax block into a grove with a torch (be careful) and stick a strip of foundation in there. The wax will drip/pour nicely off of a bottom corner. You can't be timid about this because the wax will cool and harden. Just fill the groove reasonably quickly and it'll stay soft enough to join with the foundation. I've never had cross comb and the only annoyance is if I make them too short (more than an inch from the side) because they'll start to curve the ends.Stuart

melting wax.jpg installing foundation.jpg

That's what I do but, with plastic and glue.

**Marsh** · 12-09-2012, 03:34 PM

Linda's method is very good, but I just use regular glue in my slot to hold the foundation strip and it does not bother the bees. I have used it for 2 years. I just put a very small bead in the slot and always leave a strip on the top bar when I cut off the honeycomb. Some people may not like my method, but ti works with no side effects.