I just saw the saw on the internet and was wondering if it would work in making wooden ware. I do not know anything about wood working but would like to be able to make my own hive equipment. Please let me know what you all think.
I do not like the all in one thing. Get the right tool for the job.
What i have for making nuc boxes, lids, bottoms, etc-
70s Craftsman Table saw (the best saw short of a uni saw) with 24" rip- crucial to making lids. $150
Dado set $50
Cheap off brand skill saw $30
Craftsman Sliding miter saw $200
A good tape measure, a square, and a steady hand- Priceless
I don't see much use for that saw in making hive equipment. If I had to pick only one saw in my little shop to keep, it would be the Craftsman table saw with 48" table that I bought used for $75 bucks. It can rip, crosscut, cut box joints and dado grooves. Just about every basic operation needed in making hives. (Except sanding and drilling.)
Don't buy one of the many $99 table saw specials that big-box stores offer. You need to make sure that your table saw can handle a 3/4" stack of dado blades. Most of the little cheap saws do not have an arbor long enough for a stack of blades this wide and without the ability to dado, the saw is useless to me.
And don't buy a Craftsman anything. Look for an old Rockwell or Delta. I have a Rockwell that I bought in 1973. Have made thousands of supers, bottoms, etc. Can still buy parts. Buy quality, it lasts.
Got an early 70's era 12" craftsman table saw with a broken motor I would give away to anyone wanting to pick it up. The arbor comes directly out of the motor so unless someone knows where to find a replacement motor the only thing it would be good for would be for a retrofitting project.
I also second avoiding the big box store $100 saw. The craftsman i have is my second born, my other saw is a small skil. I will set it up with a dado set so i do not have to keep switching blades.
Just got to looking at your local craigslist. I have this exact saw-http://columbia.craigslist.org/tls/2161126703.html
Keep looking for the next couple of months on craigslist you will find something.
I agree that if you watch Craigslist, you can find what you need. A decent table saw will do just about everything you need to build hives. If you build a sled for a table saw, you can cross cut long wide boards to size, accuartly.
Since you have never used one, please do some research on safety. They will kick back and they just love tasty little fingers which they will eat very fast.
A riving knife is nice to prevent kick back, if you can find a saw with one, and before you make your first cut, have an assortment of push sticks ready.
I hate to sound like somebodys mother, but I have cut myself doing something stoopid. I didn't loose my appendages, but it was ugly...very, very ugly. And it hurt for days and days.
Be careful.
I agree with most of the other posts! Get a good table saw! I have an antique Sears 10", it is a work horse. Also have a radial arm and a band saw. Looking at the Rockwell thing, I would love to see a rabbit or frame rest cut with it???? Get the correct tool for the job!!
As someone else pointed out - saws just love to eat fingers - YUM!
I just retired my 50+ year old Craftsman 9" table saw. The thing weighs about 400 pounds just sitting there but it did cut well. Needed another motor and the blades are getting hard to find. Replaced it with a Ridgid cabinet saw and it seems to be fine. Like the others said, a good table saw will do you just fine. I make my own woodenware, except for the frames. Nearly everything is done on the table saw. Some of the cuts are made on the miter saw and some of the holes for the ventilated top covers are done on the drill press but the bulk of the work is done on the table saw.
We have Delta table saw/jointer that was purchased shortly after WWII. Works well for ripping 2 x 6's down to 3/8th. A small, cheesy Sears 8" saw is just that, Cheesy, but with a thin kerf blade, and a rigid jury rigged fence, is adequate for cutting up 3/4 " lumber. For cut off, A millwaukee slider performs well. But nothing beats the 12" 3 phase Powermatic planer. It makes short work of planing the 3/8 boards.
The bottom line is, pick the machine and tooling that best suites the work you want to do. When set up right, you will "make it look easy".
Kingfisher check out delta fence at tool barn .com or something close cost me just less than 150 in the door about 2 hrs to install on old craftsman table saw (some drilling and taping) works great
If you really don't know anything about wood working you might consider just buying your woodenware.
It takes more than just a saw - especially it takes some kind of space to do the work in. And there are real, serious safety considerations - as in a lot of your future conversations could begin with someone asking you - "How did that happen?"
You might consider taking a class at a tech school - you might not even like woodworking.
I don't want to discourage you if you want to take up woodworking. But if you are going to buy tools and everything to save money on hobby beekeeping equipment it might not make sense. Even if you already have the tools unless you have a good source of materials (besides the big box home improvement store) you might not even save much money. If you aren't careful it could cost considerably more.
There it is there. You can't save much buying from the big box stores. They told me I would have to spend $2500.00 to even get a slight discount. If you know a contractor that buys huge bundles, you may be able to piggyback on his purchases and see some decent savings.
Tearing down old buildings will give you some nice lumber. I'm looking at one really old house now that has 1X12s for sheating on the roof and walls. Those are few and far between though.
You need to figure how much your boxes will cost if you build them and how much with shipping, if you buy them. If you live close enough to pick them up, they will probably be cheaper than building them without the shipping.
If you have to buy all your tools to get started, it could be cost prohibitive all the way around.
Even if you were to buy boxes and frames, there are still lots of things you can make like nuc boxes,inner covers,telescoping covers,screened bottom boards and slatted racks if you use those, observation hive, plus all the projects you can do around the house. I got a used Craftsman table saw back in the mid seventies. All cast Iron including the extensions. It's still going strong. As mentioned by others, a replacement fence doubles the usefulness.
Never go to lowes or hd for lumber. Go find a local hardware store. I get my staples for $10/5000, cd exterior plywood ($16/.5 inch, $21/ 5/8s), 1x12x8 6.50 or less, cannot remember, nails for $1.10 a pound, deck screws at 3.29 a pound, etc. I have saved TONS on money there. Lowes and HD are out to rob you!
MIke
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Beesource Beekeeping Forums
1.8M posts
54.7K members
Since 1999
A forum community dedicated to beekeeping, bee owners and enthusiasts. Come join the discussion about breeding, honey production, health, behavior, hives, housing, adopting, care, classifieds, and more!